@c -*-texinfo-*- @c This file is part of the StarPU Handbook. @c Copyright (C) 2009--2011 Universit@'e de Bordeaux 1 @c Copyright (C) 2010, 2011, 2012, 2013 Centre National de la Recherche Scientifique @c Copyright (C) 2011 Institut National de Recherche en Informatique et Automatique @c See the file starpu.texi for copying conditions. TODO: improve! @menu * Data management:: * Task granularity:: * Task submission:: * Task priorities:: * Task scheduling policy:: * Performance model calibration:: * Task distribution vs Data transfer:: * Data prefetch:: * Power-based scheduling:: * Static scheduling:: * Profiling:: * CUDA-specific optimizations:: * Performance debugging:: * Simulated performance:: @end menu Simply encapsulating application kernels into tasks already permits to seamlessly support CPU and GPUs at the same time. To achieve good performance, a few additional changes are needed. @node Data management @section Data management When the application allocates data, whenever possible it should use the @code{starpu_malloc} function, which will ask CUDA or OpenCL to make the allocation itself and pin the corresponding allocated memory. This is needed to permit asynchronous data transfer, i.e. permit data transfer to overlap with computations. Otherwise, the trace will show that the @code{DriverCopyAsync} state takes a lot of time, this is because CUDA or OpenCL then reverts to synchronous transfers. By default, StarPU leaves replicates of data wherever they were used, in case they will be re-used by other tasks, thus saving the data transfer time. When some task modifies some data, all the other replicates are invalidated, and only the processing unit which ran that task will have a valid replicate of the data. If the application knows that this data will not be re-used by further tasks, it should advise StarPU to immediately replicate it to a desired list of memory nodes (given through a bitmask). This can be understood like the write-through mode of CPU caches. @cartouche @smallexample starpu_data_set_wt_mask(img_handle, 1<<0); @end smallexample @end cartouche will for instance request to always automatically transfer a replicate into the main memory (node 0), as bit 0 of the write-through bitmask is being set. @cartouche @smallexample starpu_data_set_wt_mask(img_handle, ~0U); @end smallexample @end cartouche will request to always automatically broadcast the updated data to all memory nodes. Setting the write-through mask to @code{~0U} can also be useful to make sure all memory nodes always have a copy of the data, so that it is never evicted when memory gets scarse. Implicit data dependency computation can become expensive if a lot of tasks access the same piece of data. If no dependency is required on some piece of data (e.g. because it is only accessed in read-only mode, or because write accesses are actually commutative), use the @code{starpu_data_set_sequential_consistency_flag} function to disable implicit dependencies on that data. In the same vein, accumulation of results in the same data can become a bottleneck. The use of the @code{STARPU_REDUX} mode permits to optimize such accumulation (@pxref{Data reduction}). To a lesser extent, the use of the @code{STARPU_COMMUTE} flag keeps the bottleneck, but at least permits the accumulation to happen in any order. Applications often need a data just for temporary results. In such a case, registration can be made without an initial value, for instance this produces a vector data: @cartouche @smallexample starpu_vector_data_register(&handle, -1, 0, n, sizeof(float)); @end smallexample @end cartouche StarPU will then allocate the actual buffer only when it is actually needed, e.g. directly on the GPU without allocating in main memory. In the same vein, once the temporary results are not useful any more, the data should be thrown away. If the handle is not to be reused, it can be unregistered: @cartouche @smallexample starpu_unregister_submit(handle); @end smallexample @end cartouche actual unregistration will be done after all tasks working on the handle terminate. If the handle is to be reused, instead of unregistering it, it can simply be invalidated: @cartouche @smallexample starpu_invalidate_submit(handle); @end smallexample @end cartouche the buffers containing the current value will then be freed, and reallocated only when another task writes some value to the handle. @node Task granularity @section Task granularity Like any other runtime, StarPU has some overhead to manage tasks. Since it does smart scheduling and data management, that overhead is not always neglectable. The order of magnitude of the overhead is typically a couple of microseconds, which is actually quite smaller than the CUDA overhead itself. The amount of work that a task should do should thus be somewhat bigger, to make sure that the overhead becomes neglectible. The offline performance feedback can provide a measure of task length, which should thus be checked if bad performance are observed. To get a grasp at the scalability possibility according to task size, one can run @code{tests/microbenchs/tasks_size_overhead.sh} which draws curves of the speedup of independent tasks of very small sizes. The choice of scheduler also has impact over the overhead: for instance, the @code{dmda} scheduler takes time to make a decision, while @code{eager} does not. @code{tasks_size_overhead.sh} can again be used to get a grasp at how much impact that has on the target machine. @node Task submission @section Task submission To let StarPU make online optimizations, tasks should be submitted asynchronously as much as possible. Ideally, all the tasks should be submitted, and mere calls to @code{starpu_task_wait_for_all} or @code{starpu_data_unregister} be done to wait for termination. StarPU will then be able to rework the whole schedule, overlap computation with communication, manage accelerator local memory usage, etc. @node Task priorities @section Task priorities By default, StarPU will consider the tasks in the order they are submitted by the application. If the application programmer knows that some tasks should be performed in priority (for instance because their output is needed by many other tasks and may thus be a bottleneck if not executed early enough), the @code{priority} field of the task structure should be set to transmit the priority information to StarPU. @node Task scheduling policy @section Task scheduling policy By default, StarPU uses the @code{eager} simple greedy scheduler. This is because it provides correct load balance even if the application codelets do not have performance models. If your application codelets have performance models (@pxref{Performance model example} for examples showing how to do it), you should change the scheduler thanks to the @code{STARPU_SCHED} environment variable. For instance @code{export STARPU_SCHED=dmda} . Use @code{help} to get the list of available schedulers. The @b{eager} scheduler uses a central task queue, from which workers draw tasks to work on. This however does not permit to prefetch data since the scheduling decision is taken late. If a task has a non-0 priority, it is put at the front of the queue. The @b{prio} scheduler also uses a central task queue, but sorts tasks by priority (between -5 and 5). The @b{random} scheduler distributes tasks randomly according to assumed worker overall performance. The @b{ws} (work stealing) scheduler schedules tasks on the local worker by default. When a worker becomes idle, it steals a task from the most loaded worker. The @b{dm} (deque model) scheduler uses task execution performance models into account to perform an HEFT-similar scheduling strategy: it schedules tasks where their termination time will be minimal. The @b{dmda} (deque model data aware) scheduler is similar to dm, it also takes into account data transfer time. The @b{dmdar} (deque model data aware ready) scheduler is similar to dmda, it also sorts tasks on per-worker queues by number of already-available data buffers. The @b{dmdas} (deque model data aware sorted) scheduler is similar to dmda, it also supports arbitrary priority values. The @b{heft} (heterogeneous earliest finish time) scheduler is deprecated. It is now just an alias for @b{dmda}. The @b{pheft} (parallel HEFT) scheduler is similar to heft, it also supports parallel tasks (still experimental). The @b{peager} (parallel eager) scheduler is similar to eager, it also supports parallel tasks (still experimental). @node Performance model calibration @section Performance model calibration Most schedulers are based on an estimation of codelet duration on each kind of processing unit. For this to be possible, the application programmer needs to configure a performance model for the codelets of the application (see @ref{Performance model example} for instance). History-based performance models use on-line calibration. StarPU will automatically calibrate codelets which have never been calibrated yet, and save the result in @code{$STARPU_HOME/.starpu/sampling/codelets}. The models are indexed by machine name. To share the models between machines (e.g. for a homogeneous cluster), use @code{export STARPU_HOSTNAME=some_global_name}. To force continuing calibration, use @code{export STARPU_CALIBRATE=1} . This may be necessary if your application has not-so-stable performance. StarPU will force calibration (and thus ignore the current result) until 10 (_STARPU_CALIBRATION_MINIMUM) measurements have been made on each architecture, to avoid badly scheduling tasks just because the first measurements were not so good. Details on the current performance model status can be obtained from the @code{starpu_perfmodel_display} command: the @code{-l} option lists the available performance models, and the @code{-s} option permits to choose the performance model to be displayed. The result looks like: @example $ starpu_perfmodel_display -s starpu_dlu_lu_model_22 performance model for cpu # hash size mean dev n 880805ba 98304 2.731309e+02 6.010210e+01 1240 b50b6605 393216 1.469926e+03 1.088828e+02 1240 5c6c3401 1572864 1.125983e+04 3.265296e+03 1240 @end example Which shows that for the LU 22 kernel with a 1.5MiB matrix, the average execution time on CPUs was about 11ms, with a 3ms standard deviation, over 1240 samples. It is a good idea to check this before doing actual performance measurements. A graph can be drawn by using the @code{starpu_perfmodel_plot}: @example $ starpu_perfmodel_plot -s starpu_dlu_lu_model_22 98304 393216 1572864 $ gnuplot starpu_starpu_dlu_lu_model_22.gp $ gv starpu_starpu_dlu_lu_model_22.eps @end example If a kernel source code was modified (e.g. performance improvement), the calibration information is stale and should be dropped, to re-calibrate from start. This can be done by using @code{export STARPU_CALIBRATE=2}. Note: due to CUDA limitations, to be able to measure kernel duration, calibration mode needs to disable asynchronous data transfers. Calibration thus disables data transfer / computation overlapping, and should thus not be used for eventual benchmarks. Note 2: history-based performance models get calibrated only if a performance-model-based scheduler is chosen. The history-based performance models can also be explicitly filled by the application without execution, if e.g. the application already has a series of measurements. This can be done by using @code{starpu_perfmodel_update_history}, for instance: @cartouche @smallexample static struct starpu_perfmodel perf_model = @{ .type = STARPU_HISTORY_BASED, .symbol = "my_perfmodel", @}; struct starpu_codelet cl = @{ .where = STARPU_CUDA, .cuda_funcs = @{ cuda_func1, cuda_func2, NULL @}, .nbuffers = 1, .modes = @{STARPU_W@}, .model = &perf_model @}; void feed(void) @{ struct my_measure *measure; struct starpu_task task; starpu_task_init(&task); task.cl = &cl; for (measure = &measures[0]; measure < measures[last]; measure++) @{ starpu_data_handle_t handle; starpu_vector_data_register(&handle, -1, 0, measure->size, sizeof(float)); task.handles[0] = handle; starpu_perfmodel_update_history(&perf_model, &task, STARPU_CUDA_DEFAULT + measure->cudadev, 0, measure->implementation, measure->time); starpu_task_clean(&task); starpu_data_unregister(handle); @} @} @end smallexample @end cartouche Measurement has to be provided in milliseconds for the completion time models, and in Joules for the energy consumption models. @node Task distribution vs Data transfer @section Task distribution vs Data transfer Distributing tasks to balance the load induces data transfer penalty. StarPU thus needs to find a balance between both. The target function that the @code{dmda} scheduler of StarPU tries to minimize is @code{alpha * T_execution + beta * T_data_transfer}, where @code{T_execution} is the estimated execution time of the codelet (usually accurate), and @code{T_data_transfer} is the estimated data transfer time. The latter is estimated based on bus calibration before execution start, i.e. with an idle machine, thus without contention. You can force bus re-calibration by running @code{starpu_calibrate_bus}. The beta parameter defaults to 1, but it can be worth trying to tweak it by using @code{export STARPU_SCHED_BETA=2} for instance, since during real application execution, contention makes transfer times bigger. This is of course imprecise, but in practice, a rough estimation already gives the good results that a precise estimation would give. @node Data prefetch @section Data prefetch The @code{heft}, @code{dmda} and @code{pheft} scheduling policies perform data prefetch (see @ref{STARPU_PREFETCH}): as soon as a scheduling decision is taken for a task, requests are issued to transfer its required data to the target processing unit, if needeed, so that when the processing unit actually starts the task, its data will hopefully be already available and it will not have to wait for the transfer to finish. The application may want to perform some manual prefetching, for several reasons such as excluding initial data transfers from performance measurements, or setting up an initial statically-computed data distribution on the machine before submitting tasks, which will thus guide StarPU toward an initial task distribution (since StarPU will try to avoid further transfers). This can be achieved by giving the @code{starpu_data_prefetch_on_node} function the handle and the desired target memory node. @node Power-based scheduling @section Power-based scheduling If the application can provide some power performance model (through the @code{power_model} field of the codelet structure), StarPU will take it into account when distributing tasks. The target function that the @code{dmda} scheduler minimizes becomes @code{alpha * T_execution + beta * T_data_transfer + gamma * Consumption} , where @code{Consumption} is the estimated task consumption in Joules. To tune this parameter, use @code{export STARPU_SCHED_GAMMA=3000} for instance, to express that each Joule (i.e kW during 1000us) is worth 3000us execution time penalty. Setting @code{alpha} and @code{beta} to zero permits to only take into account power consumption. This is however not sufficient to correctly optimize power: the scheduler would simply tend to run all computations on the most energy-conservative processing unit. To account for the consumption of the whole machine (including idle processing units), the idle power of the machine should be given by setting @code{export STARPU_IDLE_POWER=200} for 200W, for instance. This value can often be obtained from the machine power supplier. The power actually consumed by the total execution can be displayed by setting @code{export STARPU_PROFILING=1 STARPU_WORKER_STATS=1} . On-line task consumption measurement is currently only supported through the @code{CL_PROFILING_POWER_CONSUMED} OpenCL extension, implemented in the MoviSim simulator. Applications can however provide explicit measurements by using the @code{starpu_perfmodel_update_history} function (examplified in @ref{Performance model example} with the @code{power_model} performance model. Fine-grain measurement is often not feasible with the feedback provided by the hardware, so the user can for instance run a given task a thousand times, measure the global consumption for that series of tasks, divide it by a thousand, repeat for varying kinds of tasks and task sizes, and eventually feed StarPU with these manual measurements through @code{starpu_perfmodel_update_history}. @node Static scheduling @section Static scheduling In some cases, one may want to force some scheduling, for instance force a given set of tasks to GPU0, another set to GPU1, etc. while letting some other tasks be scheduled on any other device. This can indeed be useful to guide StarPU into some work distribution, while still letting some degree of dynamism. For instance, to force execution of a task on CUDA0: @cartouche @smallexample task->execute_on_a_specific_worker = 1; task->worker = starpu_worker_get_by_type(STARPU_CUDA_WORKER, 0); @end smallexample @end cartouche @node Profiling @section Profiling A quick view of how many tasks each worker has executed can be obtained by setting @code{export STARPU_WORKER_STATS=1} This is a convenient way to check that execution did happen on accelerators without penalizing performance with the profiling overhead. A quick view of how much data transfers have been issued can be obtained by setting @code{export STARPU_BUS_STATS=1} . More detailed profiling information can be enabled by using @code{export STARPU_PROFILING=1} or by calling @code{starpu_profiling_status_set} from the source code. Statistics on the execution can then be obtained by using @code{export STARPU_BUS_STATS=1} and @code{export STARPU_WORKER_STATS=1} . More details on performance feedback are provided by the next chapter. @node CUDA-specific optimizations @section CUDA-specific optimizations Due to CUDA limitations, StarPU will have a hard time overlapping its own communications and the codelet computations if the application does not use a dedicated CUDA stream for its computations instead of the default stream, which synchronizes all operations of the GPU. StarPU provides one by the use of @code{starpu_cuda_get_local_stream()} which can be used by all CUDA codelet operations to avoid this issue. For instance: @cartouche @smallexample func <<>> (foo, bar); cudaStreamSynchronize(starpu_cuda_get_local_stream()); @end smallexample @end cartouche StarPU already does appropriate calls for the CUBLAS library. Unfortunately, some CUDA libraries do not have stream variants of kernels. That will lower the potential for overlapping. @node Performance debugging @section Performance debugging To get an idea of what is happening, a lot of performance feedback is available, detailed in the next chapter. The various informations should be checked for. @itemize @item What does the Gantt diagram look like? (see @ref{Gantt diagram}) @itemize @item If it's mostly green (tasks running in the initial context) or context specific color prevailing, then the machine is properly utilized, and perhaps the codelets are just slow. Check their performance, see @ref{Codelet performance}. @item If it's mostly purple (FetchingInput), tasks keep waiting for data transfers, do you perhaps have far more communication than computation? Did you properly use CUDA streams to make sure communication can be overlapped? Did you use data-locality aware schedulers to avoid transfers as much as possible? @item If it's mostly red (Blocked), tasks keep waiting for dependencies, do you have enough parallelism? It might be a good idea to check what the DAG looks like (see @ref{DAG}). @item If only some workers are completely red (Blocked), for some reason the scheduler didn't assign tasks to them. Perhaps the performance model is bogus, check it (see @ref{Codelet performance}). Do all your codelets have a performance model? When some of them don't, the schedulers switches to a greedy algorithm which thus performs badly. @end itemize @end itemize You can also use the Temanejo task debugger (see @ref{Task debugger}) to visualize the task graph more easily. @node Simulated performance @section Simulated performance StarPU can use Simgrid in order to simulate execution on an arbitrary platform. @subsection Calibration The idea is to first compile StarPU normally, and run the application, so as to automatically benchmark the bus and the codelets. @smallexample $ ./configure && make $ STARPU_SCHED=dmda ./examples/matvecmult/matvecmult [starpu][_starpu_load_history_based_model] Warning: model matvecmult is not calibrated, forcing calibration for this run. Use the STARPU_CALIBRATE environment variable to control this. $ ... $ STARPU_SCHED=dmda ./examples/matvecmult/matvecmult TEST PASSED @end smallexample Note that we force to use the dmda scheduler to generate performance models for the application. The application may need to be run several times before the model is calibrated. @subsection Simulation Then, recompile StarPU, passing @code{--enable-simgrid} to @code{./configure}, and re-run the application: @smallexample $ ./configure --enable-simgrid && make $ STARPU_SCHED=dmda ./examples/matvecmult/matvecmult TEST FAILED !!! @end smallexample It is normal that the test fails: since the computation are not actually done (that is the whole point of simgrid), the result is wrong, of course. If the performance model is not calibrated enough, the following error message will be displayed @smallexample $ STARPU_SCHED=dmda ./examples/matvecmult/matvecmult [starpu][_starpu_load_history_based_model] Warning: model matvecmult is not calibrated, forcing calibration for this run. Use the STARPU_CALIBRATE environment variable to control this. [starpu][_starpu_simgrid_execute_job][assert failure] Codelet matvecmult does not have a perfmodel, or is not calibrated enough @end smallexample The number of devices can be chosen as usual with @code{STARPU_NCPU}, @code{STARPU_NCUDA}, and @code{STARPU_NOPENCL}. For now, only the number of cpus can be arbitrarily chosen. The number of CUDA and OpenCL devices have to be lower than the real number on the current machine. The amount of simulated GPU memory is for now unbound by default, but it can be chosen by hand through the @code{STARPU_LIMIT_CUDA_MEM}, @code{STARPU_LIMIT_CUDA_devid_MEM}, @code{STARPU_LIMIT_OPENCL_MEM}, and @code{STARPU_LIMIT_OPENCL_devid_MEM} environment variables. The Simgrid default stack size is small; to increase it use the parameter @code{--cfg=contexts/stack_size}, for example: @smallexample $ ./example --cfg=contexts/stack_size:8192 TEST FAILED !!! @end smallexample Note: of course, if the application uses @code{gettimeofday} to make its performance measurements, the real time will be used, which will be bogus. To get the simulated time, it has to use @code{starpu_timing_now} which returns the virtual timestamp in ms. @subsection Simulation on another machine The simgrid support even permits to perform simulations on another machine, your desktop, typically. To achieve this, one still needs to perform the Calibration step on the actual machine to be simulated, then copy them to your desktop machine (the @code{$STARPU_HOME/.starpu} directory). One can then perform the Simulation step on the desktop machine, by setting the @code{STARPU_HOSTNAME} environment variable to the name of the actual machine, to make StarPU use the performance models of the simulated machine even on the desktop machine. If the desktop machine does not have CUDA or OpenCL, StarPU is still able to use simgrid to simulate execution with CUDA/OpenCL devices, but the application source code will probably disable the CUDA and OpenCL codelets in that case. Since during simgrid execution, the functions of the codelet are actually not called, one can use dummy functions such as the following to still permit CUDA or OpenCL execution: @smallexample static struct starpu_codelet cl11 = @{ .cpu_funcs = @{chol_cpu_codelet_update_u11, NULL@}, .cpu_funcs_name = @{"chol_cpu_codelet_update_u11", NULL@}, #ifdef STARPU_USE_CUDA .cuda_funcs = @{chol_cublas_codelet_update_u11, NULL@}, #elif defined(STARPU_SIMGRID) .cuda_funcs = @{(void*)1, NULL@}, #endif .nbuffers = 1, .modes = @{STARPU_RW@}, .model = &chol_model_11 @}; @end smallexample